With all the overall benefits and drawbacks of a wing considered, I decided to put a bigger, sportier wing on my Alto Works. There were a few existing ones from some manufacturers like Jaws Yamamoto and TAKE OFF, but I came across this gorgeous TRUST / GReddy carbon fiber wing. While it wasn’t in perfect condition, as it came used, it still is absolutely beautiful and it would really go well with the rest of my modifications.

Wait, you might be asking, “Does GReddy make a CF rear wing for the Alto Works?” (Okay, maybe you’re not asking that.)

You better darn bet they don’t! This wing comes courtesy of my Suzuki Swift Sport, which was removed in preparation to sell the car. I know well the lack of value aftermarket parts have on cars, if not devaluing a used car even more due to the sign that the car was modified. Further, the GReddy spoiler, while quite beautiful in these photos, have long since succumbed to outdoor weather in the years it was installed on the car with the clear coat faded and some discoloration present. With a professional clear coat, it might be once again worth a bit of money, but in its present state it would have only ruined the Swift’s otherwise beautiful appearance.

Hence, the wing was removed before I decided to sell the Swift. On the second hand market, the spoiler, even in its current state, might fetch 5000￥ or more, given that it is a model-specific, full CF piece no longer in production, made by a reputable manufacturer. What would be even better would be to give it life on my Alto since the aforementioned hatchback spoilers go for around the same cost and they are nowhere near as fancy.

I’ll admit a drawback, however. Since it is not model-specific, I’ll have a few issues. First, the fit. It may not even work right or it could be loose. Secondly, it was not tested and designed for this car, so the aero benefit may be minimal, if at all. It may even cause unnecessary drag or unbalance the car.

But this is a project car, after all. Why don’t we give it a shot?

Spoiler on a spoiler so you can spoiler. This is a joke… though I was half-serious about doing this.

The original spoiler came off with four screws and a lot of old, dried, rotted double-sided tape. Sadly, due to the 3 decades since, it has become semi-permanently attached to the back of the car.

Before the other spoiler goes on, it was time to try to get the old stubborn tape off using the rubber decal remover I used on my ugly side decals awhile back. After that failed to get the desired results, I resorted to a heat gun and pointy, sharp objects. I know it won’t be perfect and I’ll likely damage the paint, but as you can see, the paint isn’t that great to begin with.

This is probably as good as it’s gonna get without resorting to sandpaper or something harsher. The edges where the double-sided tape were created a little area where rust formed, so there are now tiny little bubbling paint spots. For now, it is all primarily surface rust. Hopefully a little touch-up is adequate for now.

And with the removal of the four screws, there are now four rubber mounting points which I cannot easily plug without a lot of filler… Well, there were 4 rubber mounts. One rubber grommet fell apart and into the roof. (No matter, I managed to fetch that out later.) Since there is no easy way to plug up the holes without going through a lot of trouble, I decided to remove the remaining rubber mounts and cover up the remainder with some CF vinyl. This will clear up the look a bit in the rear and not only hide the holes, but cover up the ruined paint back there.

There are 4 total screws holding the spoiler in place on the Swift, but due to the width of the car, in reality only two can only be used due to the mounting surface. To mount the two screws, I drilled some holes and used some blind M6 rivnuts.

Surprisingly, it was super secure with only two points of mounting. But leaving it like this would be a half-baked job.

I drilled and installed some rivnuts to my car and the spoiler to install support rods. These support rods are commonly added for extra support on the backside of spoilers and wings or in front wind splitters. They are simple threaded stainless steel or aluminum bits. Since the purpose of these supports here are to help hold the spoiler in place and the fact the spoiler isn’t designed for significant downforce, they should be more than enough to help secure it.

The wing is bolted on and super secure! You can literally shake the whole car by the wing and rods.

Overall, this project was a simple one that really enhances the look of the car. Although upon closer inspection, one can tell this wing was not made for this car, but even then it still gives off a very custom, racing aura. Definitely one of my best appearance modifications so far.

But I have more to do yet!